Right Angle Block. The 15 mm version of the block that started it all over 20 years ago. This block is the workhorse of the Berkey System. These blocks are available in both a left and right hand version. This allows access to the fastener even if you have two blocks side by side. An equal number of each is recommended. You can never have too many of these. Bore size is 15 mm and works well with all 15 mm tubing from other manufacturers.

Gain control of your controls with this dual handle set created for the Sony FS-700. This handle set utilizes our Sony Rosette to allow the user to use the factory Sony handle and controls. This is one of the lightest and most versatile handle sets available. Slide these onto any iris rods that are spaced at 60 mm. The weight for this handle set is just one pound. Individual control of each handle is made possible via the two Spud Blocks on each handle allowing any angle or spacing desired. Handles shown are spaced 10 inches apart but can be adjusted to any width. The handle rods have an internal 1/2-13 thread allowing you to easily lengthen them to your needs by adding Rod Extensions  (sold separately). Sony grip not included.

The 3 inch diameter suction base creates a strong vacuum with just a few strokes on the built-in pump. A red ring indicator on the pump button lets you know when you have insufficient vacuum. Use the lift tabs to break the suction. Comes with the Berkey System mounting plate on top that is drilled and tapped for two 1/4-20 fasteners and cup protector. Mount anything on any flat or slightly curved non-porous smooth surface. Fun! Maximum temp. is 120 F. Lifting capacity is 15 pounds.

The 7 inch diameter suction base creates a strong vacuum with just a few strokes on the built-in pump. A red ring indicator on the pump button lets you know when you have insufficient vacuum. Use the lift tabs to break the suction. Comes drilled and tapped for two 1/4-20 fasteners and cup protector. Mount anything on any flat or slightly curved non-porous smooth surface. Fun! Maximum temp. is 120° F. Lifting capacity is 70 pounds.

Need to mount you camera in the strangest places and have it work with existing grip gear? Now you can. Just insert the 15 mm end into any 15 mm series block and make new friends with all the grips. Also available in 500 and 750/19mm series.

We've all been there, you're on the set with the coolest damn rig that you've ever built and some grip comes up to you and says "How come this stuff isn't made in 5/8th's inch so it will work with my C-stands?". Now it can work with any standard grip gear to or from your rig. Just attach this rod to any 500 series block and make new friends with all the grips.

We've all been there; you're on the set with the coolest rig that you've ever built and some grip comes up to you and says "How come this stuff isn't made in 5/8th's inch so it will work with my C-stands?".  Now it can work with any standard grip gear to or from your rig.  Just attach this rod to any 750/19mm  series block and make new friends with all the grips.  Available in 15 mm, 500 and 750/19mm Series.

A Multi-use Camera mounting plate that allows the user to mount DSLR or standard video cameras. Versatile design allows the base to be rotated to accommodate a wide range of camera body styles. Plate has 2.5mm lateral adjustment to allow for cameras with off axis mounting. Two large anti-slip pads ensure the camera is gripped securely.

Our indexable spring loaded ratcheting lever allows the user to position the lever where they like by simply pulling the lever out and rotating it to the desired position. Six positions available. Thread is 10-32 and the thread length is 5/8th's of an inch long. These can be used as a direct replacement for any of our standard single ended knobs.

Cheese style base plate 2 inches by 4 inches with 3/8-16 and 1/4-20 tapped holes for tripod or 3^rd party quick release plates.  Additionally, 10-32 tapped and #10 counter bores are provided in a number of locations for mounting the vertical posts for a Camera Baseplate.  A Cross Block can be added for those that wish to add cages, extra handles or a shoulder pad.  This plate can also be used as a universal cheese plate to mount battery pack, memory devices and other items.

Camera Base Plate made specifically for the Sony F3 and Panasonic AF cameras. If you already own one of our DSLR camera Base Assemblies and would like to mount your Sony F3, you can purchase this Base Plate. This baseplate is designed to the exact mounting pattern of the Sony F3. Camera Mounting Knobs sold separately. Fits many other large bodied cameras.

Large mounting plate for the Sony F3, Panasonic AF and other large body cameras. It is compatible with all of our Camera Base Plates. For easy mounting, it has rows of tapped holes (10-32, 1/4-20, and 3/8-16), rows of counter-bored holes (10-32), and clearance holes for 1/4" fasteners. The bottom face of this plate is drilled and tapped to all the user to interface it with an Arri Bridge Plate. Additional holes are provided to accommodate any quick release or dovetail plate.

The Mikro Camera Base Plate may looks small, but it can do a lot. It is only 1.8" x 2.25", but is compatible with most accessories.
Camera Mounting Knob sold separately.

This is the perfect little accessory for mounting the Mini Camera Baseplate to your tripod. No tools needed to remove your Mini from the Mini Runner rig and mount it to the posts. The two knobs on the Mini allow it to be changed over in seconds. A Quad Block and iris rods can also be added or removed in seconds.

Multi-function camera base plate component. When used for a camera base, this plate is the bottom plate. Drilled and tapped for 1/4-20. Additional holes are drilled and tapped 10-32 to accept our Cross Clamp, for those that wish to add cages, extra handles and shoulder pads to a camera base. This plate can also be used as a universal cheese plate to mount battery pack, memory devices and other items.

The Mini Baseplate is one compact little camera base. This is the baseplate for run and gun rigs. Super light and compact. You can mount it to your rig using just one tube. If you need to add a follow focus or matte box, you can add a second tube and the quad block to give you the option of adding iris rods coming out the front.

These Camera Mounting Knobs are as beautiful as they are functional. For most applications the incredibly light, all aluminum version, is the ideal choice. Designed to work on all of our Camera Base Plates, the 1.1" diameter provides secure mounting and easy access. Captive threads help prevent loss.

The Cross Clamp provides a light-weight yet solid means for creating cages, handle mounts, and more. When used in conjunction with any of our camera base plates, or rail blocks, the user can create cages, secondary handles, or anything else you can dream up.

These Camera Mounting Knobs are as beautiful as they are functional. Designed to work on all of our Camera Base Plates, the 1.1" diameter provides secure mounting and easy access. The Socket Head version with a stainless steel fastener allow additional tightening for larger cameras or where access is limited. Captive threads help to prevent loss.

Vertical Posts are used for connecting Tripod Baseplates to Camera Baseplates.They allow vertical adjustment of the Iris Rods when used with the 60mm QuadBlock. Vertical Posts are available in 1.0",  1.5", 2.0" and 2.5" lengths to suit your specific needs. The 10-32 female threads in both ends allows mounting to any of our Baseplates. Vertical Posts are sold only in pairs.

This Accessory Mounting Block has five 1/4-20 tapped holes on it. You can screw any male 1/4-20 onto it and mount it just about anywhere on any 15mm tube.

This Accessory Mounting Block has four 3/8-16 tapped holes on it. You can screw any male 3/8-16 onto it and mount it just about anywhere on any 15mm tube.

This Accessory Mounting Block has four 3/8-16 tapped holes on it. You can screw any male 3/8-16 onto it and mount it just about anywhere on any 15mm tube.

This Accessory Mounting Block has five 1/4-20 tapped holes on it. You can screw any male 1/4-20 onto it and mount it just about anywhere on any 15mm tube.

This Accessory Mounting Block allows almost anything that has a 1/4-20 tapped on it to be mounted just about anywhere on any 15mm tube. The block can be mounted vertically or horizontally. One 1/4-20 socket head fastener included.

This Accessory Mounting Block allows almost anything that has a 1/4-20 tapped on it to be mounted just about anywhere on any 15mm tube. The block can be mounted in either a vertical or horizontal manner. One 1/4-20 socket head fastener included.

The spud blocks clamp to any 15mm rod or accessory allowing infinite rotational adjustment.Ideal for mounting Handles orShoulder pads.

Use this threaded spud to do just about anything you want. Great for handles.

The corner block clamps any 15mm rod or accessory at a 90 degree angle. Dual knobs allow each side to be clamped individually. The open corner design of this block allows either one of the tubes to be passed through, greatly expanding its flexibility. Ideal for cages, handle attachment, and accessory mounting.

What can we say about this block...hmmm. Not much. Some guys will find a use for it - we hope - so we made a few.

This versatile Flange Mount can be used to mount a variety of items such as  accesories to a counterweight or even the F3 Accesory Mounting Plate. The 1/2-13 tapped hole in the center can be used to mount any of our Extension Rods or the Accessory Mounting Post 1/2-13 to 1/4-20. These have many other uses and can be mounted to anything that has our standard 10-32 tapped holes on 1" centers.

The versatile Right Angle Flange Mount can be used to mount shoulder pads, accesories to a counterweight or even the F3 Accesory Mounting Plate. The 15mm spud has a 1/4-20 tapped hole in the end for additional flexibility. These have many other uses and can be mounted to anything that has our standard 10-32 tapped holes on 1" centers.

Now you can put a small cheeseplate anywhere you want. Cheeseplate is tapped with 1/4-20's on with RED spacing. The spud end fits in any 15 mm female clamp or block.

Use this Nylon Cap screw to protect your threaded rods or create a safety stop at the end of a rod. Knurled finish allows you to simply screw it onto the end of any rod by hand. The thread  is 1/2-13 and works with all Berkey System threaded rods. It also works with other manufacturers rods that have a 1/2-13 thread. This cap screw weighs next to nothing at just 4 grams. Color is black. Quantity is one.

Use this Nylon Cap screw to protect your threaded rods or create a safety stop at the end of a rod. Knurled finish allows you to simply screw it onto the end of any rod by hand. The thread is 1/2-13 and works with all Berkey System threaded rods. It also work with other manufacturers rods that have a 1/2-13 thread. This cap screw weighs next to nothing at just 4 grams. Color is black. Sold in packs of four.

The 3/16 balldriver is for use with all 1/4-20 Socket Head Cap Screws.  It is a very handy tool for assembling your rig or making quick adjustments, Bondhus Balldrivers are the preferred wrench for use with the Berkey System. Old fashioned hex wrenches are so last century. For fastest assembly, Bondhus Balldrivers are the only way to go. They fit all Berkey System components, will not over-tighten and have the ability to get into tight places.   Sold individually.

The double ended knob is a convenient and attractive upgrade for blocks purchased with screws rather than knobs. It feels as good as it looks. Two thust washers are provided for each knob.

The single ended knob is a convenient and attractive upgrade for blocks purchased with screws rather than knobs. It feels as good as it looks.  Two thust washers are provided with each knob.

A very handy tool for assembling your rig or making quick adjustments, Bondhus Balldrivers are the preferred wrench for use with the Berkey System. Old fashioned hex wrenches are so last century. For fastest assembly, Bondhus Balldrivers are the only way to go. They fit all Berkey System components, will not over-tighten and have the ability to get into tight places. Long stem also available. Sold individually.

Kipp makes this great ratcheting lever. 1.25 long lever makes it the most compact ratcheting Kipp lever available. Threads are 10-32. Threaded length is 7/8 of an inch. Color is black.

The new Sony NEX FS-100 baseplate is now available. Developed specifically for the popular FS-100, this baseplate can be configured in a number of ways to achieve perfect balance for handheld use or on a tripod. The top plate can be moved forward or rearward so that if you are running a large lens out the front or rear mount battery or other accessories in the rear,  you will be able to achieve the balance you need. The top plate can also be used separately so you can mount your dovetail plate directly to the bottom of your camera.  Read the rest of this entry »

This baseplate assembly provides a secure and solid mounting platform for large bodied cameras.  The tripod plate has enough mounting holes to attach to just about anything, including the offset mounting holes necessary for the ARRI bridge. Two mounting knobs, one on the front and the other on the rear, allow for secure camera mounting of the Sony PMW-F3 with or without tools, most other cameras use a single knob. The Quad Blocks provide vertical adjustment of the iris rods.  Read the rest of this entry »

The new Sony NEX FS-700 baseplate is available now. Developed specifically for the FS-700, this baseplate can be configured in a number of ways to achieve perfect balance for handheld use or on a tripod. The top plate can be moved forward or rearward so that if you are running a large lens out the front or rear mount battery or other accessories in the rear,  you will be able to achieve the balance you need. The top plate can also be used separately so you can mount your dovetail plate directly to the bottom of your camera.  Read the rest of this entry »

This baseplate is our entry level baseplate designed for the Blackmagic Cinema Camera. The baseplate uses our Blackmagic baseplate top mated to a Standard Rail Block and a 2X4 Tripod plate. The iris rod height is fixed at the industry standard of 85 mm to allow the use of a matte box and follow focus. The top of the plate is contoured to fit the body of the camera and gives a rock solid grip to the camera body. Read the rest of this entry »

This baseplate is designed especially for the Blackmagic Cinema Camera. The baseplate uses our Blackmagic baseplate top mated to a Quad Rail Block and a 2X4 Tripod plate. The iris rod height can be adjusted via the Quad Block up and down from the industry standard of 85 mm to 100 mm to to allow the use of any lens,  matte box and follow focus combination. The top of the plate is contoured to fit the body of the camera and gives a rock solid grip to the camera body. We have lightened this plate by fully pocketing out both top and bottom to allow proper venting of the fans on the bottom of the camera. Read the rest of this entry »

The new Sony NEX FS-700 baseplate is available now. Developed specifically for the FS-700, this is the big brother to our standard FS-700 2x4 baseplate. The 3X6 inch bottom plate gives a solid footprint and allows the use of Arri bridge plates. This baseplate can be configured in a number of ways to achieve perfect balance for handheld use or on a tripod. The top plate can be moved forward or rearward so that if you are running a large lens out the front or rear mount battery or other accessories in the rear,  you will be able to achieve the balance you need. Read the rest of this entry »

Our DSLR baseplate is the most versatile baseplate system out there. Up and down adjustment of the iris rods can be controlled via the Quad Block, so the user can use any lens, follow focus and matte box combination. The overall height of the baseplate can be changed by using different length Vertical Posts which are available in 1.5, 2 and 2.5 inch lengths, 2 inch being the most common setup.  PL mount lenses with large diameters are easily accommodated with this baseplate.  The bottom plate is drilled to accept our Cross Clamp (shown) which gives the user the ability to attach any 15mm  rod at a right angle to the iris rods. Read the rest of this entry »

Our DSLR baseplate can be configured in many ways and here's the rock solid single quad version.  Vertical adjustment of the iris rods can be controlled via the quad block so the user can use any lens, follow focus and matte box combination.  The overall height of the baseplate can be changed by using different length Vertical Posts which are available in 1.5, 2 and 2.5 inch lengths, 2 inch being the most common for most setups.   Read the rest of this entry »

The Mikro base assembly makes the perfect camera mounting platform for lightweight run and gun rigs or any time weight is a concern. Adding the quad block to the Mikro base allows rods to be added for the use of a follow focus, matte box, handles and other accessories. This baseplate assembly works great with the Panasonic GH line of cameras because it allows the user access to the battery without removing the camera from the baseplate. The bottom plate is drilled for mounting of an optional  Cross Clamp. A locating hole  is provided for the registration pin used on most quick release mounts.

The  DSLR Baseplate Assembly with Dual Quads can be configured for many different types of cameras.  The Dual Quad blocks add additional versatility. When used with longer rails the dual quad blocks setup create a rock solid platform that allows the rear rails to be used for shoulder pads, battery packs, flash drives and more. Vertical adjustment of the iris rods can be easily changed via the Quad Blocks so the user can use any lens, follow focus and matte box combination. The top Camera Baseplate can be rotated 90 degrees to accommodate wide bodied cameras.

The Mikro base assembly makes the perfect camera mounting platform for lightweight run and gun rigs or any time weight is a concern. This baseplate assembly works great with the Panasonic GH line of cameras because it allows the user access to the battery without removing the camera from the baseplate. The bottom plate is drilled for the registration pin used on most quick release mounts. And it's just plain cool. One all aluminum knob is included.

Shoulder pad with an Ultralight 60 rail block attached. This setup is great for running longer rails off the back of the shoulder pad to add counterweights and battery packs.

This versatile shoulder pad can be configured easily for all types of rigs and users. When combined with our blocks nearly any degree of rotation, tilt, and height can be achieved.

This frame allows you to quickly and easily switch your Sony PMW-F3  between tripod mount and handheld use.  When the camera is being used on a tripod, this frame allows the shoulder pad to drop down out of the way, behind the rear of the camera.  When you want to switch to handheld mode, you simply loosen two knobs on our mount, turn the assembly 180 degrees and tighten the knobs.  It fits right under our Sony F3 Camera Baseplate.  It works great with our shoulder pads which are available in several configurations to suit your needs.   Works with any camera mounted to our F3/AF baseplate with rear rods.

Import CineCity shoulder pad. Fits our Sony F3 shoulder pad frame. Pad only, shoulder pad frame sold separately. Currently sold out.

Our Chest Pad is light, compact and  just large enough to offer the support you need. When used with an Adjustable Handle Mounting Rod it can easily adjusted for comfort.

Our 3 inch wide shoulder pad with an Ultralight 60 rail block attached. Padded with 3/4 inch closed cell neoprene rubber that stay put on your shoulder. The plate has many 1/4-20 and 10-32 tapped holes to allow the user to add additional accessories.  This setup is great for running longer rails off the back of the shoulder pad to add counterweights and battery packs.

15 mm diameter carbon fiber tube. One 20 inch tube weighs just 36 grams or 1.25 ounce. Wow, that's light. The tubing is centerless ground to our specs for excellent fit and is very strong. Ends are capped. Made in USA. Rods sold individually. Currently sold out, more in stock around 4-28-13.

Our Standard Rods are light weight and very strong. Made of 15mm diameter black anodized aluminum and are available in 2, 3, 4, 6 , 7, 8, 9, 10, 12, 16, 18, 20 and 24 inch lengths. Rods sold individually.

15 mm diameter post that is tapped 1/4-20 on one end and 3/8-16 on the other end. Length is 1 inch.

Threaded 15mm rods add versatility to any rig.  Tube is 6061 Aluminum and centerless ground to ensure perfect roundness. Rods are available in 3", 6", 7", 8", 9", 10", 12", 16", 18" and 20 " lengths. A standard 1/2-13 female thread on both ends offers compatibility with rods from many other manufacturers. Rods are sold individually.

Mounting this post to any tapped 1/4-20 hole. The open end of the tube is tapped 1/2-13 to allow the user to extend the rod. Length is 2 inch. One 1/4-20 fastener included.

Rod Extensions are a convenient way to add to your rig. They are available in 3, 4, 6 and 9 inch lengths and are ideal for handle extensions or adding a counterweight to an existing rig.

Compatible with most other brands of rods with 1/2-13 threads.

Mounting this post to any tapped 1/4-20 hole. The open end of the tube is tapped 1/2-13 to allow the user to extend the rod. Length is 1 inch. One 1/4-20 fastener included.

This Accessory Mounting Post allows you to mount accessories to any of our Threaded Rods with a female 1/2-13 thread. The 1/4-20 female thread on the other end is for mounting anything with a 1/4-20 male thread. The body is 15mm diameter and 1 inch long .

Use this threaded coupler to join two or more threaded rods together. Simply tighten the single set screw in the middle for a solid lock. Works with most other manufacturers threaded tube. Thread size is 1/2-13.

Use this adapter to run your Glidecam with the Steadicam Merlin vest. Back in stock!

This Accessory Mounting Post allows you to mount accessories to just about any of our 15mm blocks. The 1/4-20 female thread on the other end is for mounting anything with a 1/4-20 male thread. The body is 15mm diameter and 1.5 inches long .

Use this threaded coupler to join two or more threaded rods together. Work with most other manufacturers threaded tube. Thread is 1/2-13.

This Accessory Mounting Post allows you to mount any accessory that has a 1/4-20 female thread. They are available in 1.5" and 2" lengths. The 1/4 20 captive screw helps to keep you from losing your knob and makes it much easier to use. It has the same high quality fluted knob that is used for camera knobs, but with a longer screw. The screw extends .25" past the end of the rod.

The Flat Top Mount is a 15 mm rod with a 3/4 inch flange on top. One female 1/4-20 tapped hole in center of rod for mounting accessories. Available in two lengths, 3/4 inch and 1 1/2 inches long.

One of the lightest and most versatile handle sets available. Slide these onto any iris rods that are spaced at 60 mm. The weight for this handle set is just one pound. Individual control of each handle is made possible via the two Spud Blocks on each handle allowing any angle or spacing desired. Handles shown are spaced 10 inches apart but can be adjusted to any width. The handle rods have an internal 1/2-13 thread allowing you to easily lengthen them to your needs by adding Rod Extensions  (sold separately).

This top handle kit for the FS700 gives you a great top handle and many mounting options. The accessory plate mounts to the two 1/4-20 holes on the top of the camera body plus the 1/4-20 on the hot shoe giving you solid mounting and all of the mounting points you will likely ever need. The top plate is ideal for mounting iris rods above your lens, an EVF or a monitor mount. This plate allows easy access to all of the camera control buttons, the factory monitor and installation takes less than one minute. Read the rest of this entry »

A remarkably light, easily adjustable solution for handles. Mount these on any 15 mm tube. Weight with hand grip, spud block, sleeves and rod is 192 grams.

This top mount accessory plate allows you to mount just about anything you can think of on top of your FS-700. The top plate is loaded with tapped holes in both the Berkey System standard and in RED standard spacing so that you can use any of our standard 15 mm accessories or any of our RED accessories to customize your FS-700 for your shooting style. Add handles, monitors, EVF's, top mount iris rods and more. Read the rest of this entry »

For ENG style shooting with the Sony FS-700, our dual rosette side handle kit is the way to go. One rosette mates with the factory Sony rosette on the side of the camera and the other rosette mates with the rosette of the Sony control handle. This relocates your factory handle to just where you want it. With this setup, the factory control handle can be pivoted, tilted, rotated and moved fore and aft for your comfort. Range of movement is 8 inches fore and aft and rotationally from the side rosette. Includes one 18 inch extension cord for the handle. Read the rest of this entry »

The top handle kit for the FS100 give you a great top handle and many mounting options. Why risk damaging your valuable camera body when there is a simple solution that offers additional protection and so many mounting options? The accessory plate mounts to the two 1/4-20 holes on the top of the  camera body plus the 1/4-20 on the hot shoe giving you solid mounting and all of the mounting points you will likely ever need. The top plate is ideal for mounting iris rods above your lens, an EVF or a monitor mount. Read the rest of this entry »

We've had quite a few customers asking for the Shorty grip assembly so we've added it to the line. The grip measures 3 inches long and the overall length is 5.25 inches long. The Delrin end cap ensures the the grip is firmly located and will not flex. The spud block allows it to be mounted on any 15 mm tube. It's a solid little grip. Weight is 98 grams.

 An ultralight and easily adjustable solution for handles. Mount these on any 15 mm tube. Weight with hand grip, spud block, sleeves and rod is 206 grams.

We've had quite a few customers asking for the Shorty grip assembly so we've added it to the line. Mount this grip on the end of any 15 mm tube The rubber grip portion measures 3 inches long and the overall length is 3.5 inches long. The Delrin end cap ensures the the grip is firmly located at the end of the tube and will not flex.  It's a solid little grip. Hex key included.

Top mounted dual handle set up. One Shorty handgrip and one standard handgrip make this one versatile grip set-up. Can be mounted in either direction. Center of grip is 3 inches above mounting position to allow the flip up monitor to move freely. There are nine tapped 1/4-20 holes on the sides of the handle mount so you can add additional components if you like. Mounting hole spacing is 36 mm. Two 1/4-20 fasteners included.

It's a handle. Two screws mount it to any 36 mm spaced holes. Mounting fasteners included.

After trying out many different grips, these were everyones favorite. The grips include our 7/8" to 15mm sleeves allowing them to be mounted anywhere on our 15mm rods. Grips are sold individualy.

Pair of 15mm to 7/8" sleeves. These sleeves allow you to use any standard size bicycle grip on any 15 mm rod and place the grip anywhere along the rod. You can also use your favorite grip by using these sleeves. Must be used with "lock-on" style bicycle grips. Sold in pairs.

An ultralight, easily adjustable solution for mounting handles or creating a rig. Mount these on any 15 mm tube. You can use these along with our Handle Grip Sleeves to mount any 7/8" clamp style grips you like. The rod is 15mm diameter and 6 inches long with a female 1/2-13 thread.

An ultralight and easily adjustable solution for mounting handles, a chest pad or creating a rig. Mount these on any 15 mm tube. You can use these along with our Handle Grip Sleeves to mount any 7/8" clamp style grips you like. The rod is 15mm diameter and 8 inches long with a female 1/2-13 thread. Sold individually.

The new VersaPlate gives users of the ability to easily mount battery packs, wireless mic brackets and many other accessories just about anywhere on your rig. Mounting hole patterns are repeated on both sides allowing mounting of a battery plate on one side and a wireless receiver holder on the other. The mounting hole patterns are clearly marked for each brand so you don't have to mess around trying to find the correct holes.  Side holes are provided for adding the BEC-ABSPU Side Plate. Read the rest of this entry »

Far more than just a weight, our modular VersaWeight system gives you the option of attaching battery packs, wireless brackets and more. Weights can also be stacked to create the right counterweight for your rig. The counterweight has tapped mounting holes on the face for mounting Anton Bauer, IDX V-Mount and BEC accessory mounting plates and brackets. A variety of our patterns of drilled and tapped holes to give you additional  mounting methods and flexible accessory attachment using a wide range of our blocks and rail blocks. Read the rest of this entry »

The PIX 240 Mounting Rod has a 15mm diameter rod 2" long with a 1/2-13 thread on the outer end providing additional accessory mounting options. It has a 1/4-20 captive screw for direct mounting to the PIX 240 and a flat flange to prevent rotation. The captive screw uses a 5/32 Allen wrench or ball driver (sold separately).

The lens support is an essential component for any rig with a long or heavy lens.  It securely mounts to the front iris rods and is easily adjustable up and down. A long 1/4-20 captive screw with an aluminum knob runs through the post and allows you to remove your lens without removing lens support or changing its adjustment.  The lens support is comprised of the Rail Block Ultra-light, an Accessory Mounting Block with counter-bore and the Accessory Mounting Post with captive screw. They are available with either a 1 1/2 inch or a 2 inch post depending on your configuration. Many other combinations can be created using different Berkey System components.

The Ultra-light Rail Block serves as a foundation for handle mounting, lens support, shoulder pad offset, and more.  There is one 1/4-20 tapped hole in the center and two 10-32 tapped holes on one inch centers. Two 10-32 fasteners included.

The Ultra-light Rail Block serves as a foundation for handle mounting, lens support, shoulder pad offset, and more.  There is one counter-bored hole for a 1/4-20 socket head screw in the center and two counter-bored holes on one inch centers for two 10-32 socket head cap screws. Two 10-32 fasteners included.

Use with any of our Camera Bases to provide vertical adjustment of Iris Rods. The innovative Quad permits vertical adjustments of the Iris Rods. It offers outstanding rigidity and quick, easy adjustments. The Quad has quickly become a popular choice for our Camera Base Plate customers.

The versatile Ultra-light serves as a foundation for rail mounting, handle mounting, shoulder pad mounting and more. Knobs are ratcheting style. Two counter bored holes for the 1/4-20 fasteners on RED spacing. Fasteners included.

The Standard 60mm Rail Block provides many options for mounting just about anything in our line. The 60mm rail block is simple and basic, yet very solid. Two 10-32 and one 1/4-20 tapped mounting holes on all 4 sides add to its understated versatility. Can be used to create a simple camera base plate, added to the cross clamp, and a whole lot more.

The Ultra-light Offset Block allows you to add a second set of rods or even a single rod to be offset in any direction. It consists of a pair of ultra-light rail blocks, one tapped and the other with recessed holes, and a spacer block. Ideal for mounting a shoulder pad.

The Dual Quad Adjustable Offset Block allows you to add a second set of rods or even a single rod to be offset in any direction. It consists of a pair of Quad Rail Blocks and a pair of 3 inch long 15mm rods. This allows for the rods to be adjusted from as little as an 19mm (3/4") center to center up to 63mm (2.5"). Any of our 15mm rods may be used with the Quads allowing longer offsets of any distance while still allowing for as little as 3/4 of an inch of offset. This is an ideal setup for mounting a shoulder pad, matte box or lens support.

The Sony NEX FS-100 Accessory Mounting Plate is now available! Why risk damaging your valuable camera body when there is a simple solution that offers additional protection and so many mounting options? The accessory plate mounts to the two 1/4-20 holes on the top of the  camera body plus the 1/4-20 on the hot shoe giving you solid mounting and all of the mounting points you will likely ever need. This is the ideal setup for mounting iris rods above your lens, a carry handle or a monitor mount. This plate allows easy access to all of the camera control buttons and installation takes less than one minute. Read the rest of this entry »

Why risk damaging your valuable camera body when there is a simple solution that  offers so many mounting options? The accessory plate mounts to the two existing 1/4-20 holes on the Sony F3 camera body, giving you all the mounting points you will likely ever need. This plate allows easy access to all of the camera control buttons. Installation takes less than one minute and the handle does not have to be removed to install it.  Read the rest of this entry »

After the introduction of the Sony F3 Top Mount Accessory Cheese Plate our customers asked us for even more mounting options. With the addition of this plate you can add many more accessories to the front of your F3 including top mounted iris rods, monitor mounting arms or even an additional small camera baseplate for a second camera. The extension plate mounts to the front two 1/4-20 holes on the Top Mount Accessory Cheese Plate and can only be used with this plate.  The plate has nine 1/4-20 and three 3/8-16 tapped holes for mounting your accessories. Read the rest of this entry »

Top Mount cheese plate for RED Epic and Scarlet. Mounting holes are tapped 1/4-20 on 9 mm centers allowing you to mount just about any RED accessory anywhere. Four additional 3/8-16 tapped holes allow even more mounting options. Side holes are 1/4-20 tapped and allow the use of other manufacturers aftermarket side handles. The underside has been pocketed out for proper venting through the top and rear of the plate. Includes mounting screws.

This small cheese plate can be mounted in any location that has tapped 1/4-20 holes on 18 mm centers. The plate measures 2.750 X 2 and has a grid of tapped 1/4-20 holes on 9 mm centers. Two mounting screws included.

The Berkey System baseplate designed for the RED Epic and Scarlet features Berkey System's Quad Block to hold the iris rods. This allows you to raise or lower your iris rods so you can use just about any lens, matte box and follow focus combination. The sides of the plate are drilled and tapped for 1/4-20 fasteners to allow the use of third party side handles. The rear of the plate is drilled and tapped to allow the use of Berkey System's Rear Extension Plate. The underside is pocketed out making this one of the lightest RED compatible baseplates available. Two stainless steel camera mounting screws included.

Need top mounted iris rods? Here's the answer. Use this small mount plate with 1.5 inch risers and a Quad block to add a height adjustable set of rails to the top of your Epic or Scarlet. Hole pattern is drill for RED spacing and can be added to either the front or rear of camera. The Quad block allows up and down adjustment. Top cheese plate and iris rods sold separately.

The Berkey System baseplate designed for the RED Epic and Scarlet features Berkey System's Quad Block to hold the iris rods. This allows you to raise or lower your iris rods so you can use just about any lens, matte box and follow focus combination. The sides of the plate are drilled and tapped for 1/4-20 fasteners to allow the use of some third party side handles. The rear of the plate is drilled and tapped to allow the use of Berkey System's Rear Extension Plate. The underside is pocketed out making this one of the lightest RED compatible baseplates available. Two stainless steel camera mounting screws included.

Add this rear extension plate to our Baseplates to give you plenty of mounting options to the rear of the camera for rear rails, shoulder pads, counterweights, batteries, memory devises... you name it. The plate is tapped for 1/4-20's, 10-32's and 1/2-13's to allow mounting just about anything you might want in back. Compatible with ViewFactor RED baseplates. Two fasteners included.

Top mounted dual handle set up. One Shorty handgrip and one standard handgrip make this one versatile grip set-up. Can be mounted in either direction. Center of grip is 3 inches above mounting position. There are nine tapped 1/4-20 holes on the sides of the handle mount so you can add additional components if you like. Mounting hole spacing is 36 mm. Two 1/4-20 fasteners included.

Use this handle mount to create handles or mount accessories. Any 15 mm tube can be mounted through the top hole. Mounting holes are 36 mm on center. Two 1/4-20 fasteners included.

Mount your Bomb EVF anywhere. Includes one mounting knob.

The Cross Clamp provides a light-weight yet solid means for creating cages, handle mounts, and more. When used in conjunction with any of our camera base plates, or rail blocks, the user can create cages, secondary handles, or anything else you can dream up. Two 1/4-20 mounting fasteners included.

Use this 60 mm block to mount rails above the lens by mounting it to the front of our Top Cheese Plate or to mount rails coming off the back on the rear of our Baseplate Rear Extension. Two knobs make removal of rods easy. Two 1/4-20 fasteners included.

Use this 60 mm block to mount rails above the lens by mounting it to the front of our Top Cheese Plate or to mount rails coming off the back on the rear of our Baseplate Rear Extension.  Two 1/4-20 fasteners included.

Top mounted dual handle set up mounts on top of our Blackmagic Cinema Camera Top Cheese Plate. One Shorty handgrip and one standard handgrip make this one versatile grip set-up. Can be mounted in either direction. Center of grip is 3 inches above mounting position. There are nine tapped 1/4-20 holes on the sides of the handle mount so you can add additional components if you like. Mounting hole spacing is 36 mm. Two 1/4-20 fasteners included.

This baseplate is designed specifically for the Sony PMW-F5 and PMW-F55. The camera is mounted to the baseplate via one 1/4-20 and one 3/8-16 captive screw. There are many positions available for these mounting screws to allow you to position the baseplate fore or aft on your camera to achieve perfect balance. The camera mounting screws both have the same hex head size so just one 5/32 hex key is required to mount your camera. Six rubber pads grip the the bottom of the camera firmly to ensure the camera does not twist on the baseplateplate. Read the rest of this entry »

This baseplate is designed specifically for the Canon EOS C100/300/500. The camera is mounted to the baseplate via one 1/4-20 and one 3/8-16 captive screw. These camera mounting screws both have the same hex head size so just one 5/32 hex key is required to mount your camera. Additional locating pins front and rear ensure that your camera stays perfectly centered and will not twist. Read the rest of this entry »

This baseplate is designed specifically for the Canon EOS C100/300/500. This version includes one Arri compatible rosette per side to allow the user to add accessories. The camera is mounted to the baseplate via one 1/4-20 and one 3/8-16 captive screw. These camera mounting screws both have the same hex head size so just one 5/32 hex key is required to mount your camera. Read the rest of this entry »

This baseplate is designed specifically for the Canon EOS C100/300/500. This version includes one 15 mm Accessory Mount Block per side to allow the user to create cages, add side handles, or add accessories to either side of the camera. The camera is mounted to the baseplate via one 1/4-20 and one 3/8-16 captive screw. These camera mounting screws both have the same hex head size so just one 5/32 hex key is required to mount your camera. Read the rest of this entry »

This lightweight top mount accessory plate allows you to mount just about anything you can think of on top of your Blackmagic Cinema Camera. The plate is loaded with 1/4-20, 3/8-16 and 10-32 tapped holes in both the Berkey System standard and one set of RED standard hole spacing so that you can use any of our standard 15 mm accessories or any of our RED accessories to customize your Blackmagic for your shooting style. The back side of the plate is pocketed out for light weight. Read the rest of this entry »

Our Blackmagic top mount cheeseplate combined with our Dual Handle assembly. Great for general camera handling and low angle shooting. The lightweight top mount accessory plate allows you to mount just about anything you can think of on top of your Blackmagic Cinema Camera. The plate is loaded with 1-4-20, 3/8-16 and 10-32 tapped holes in both the Berkey System standard and one set of RED standard hole spacing so that you can use any of our standard 15 mm accessories or any of our RED accessories to customize your Blackmagic for your shooting style. Read the rest of this entry »

Just in time for the release of the incredibly cool Sony NEX FS-700. Shipping now! This top mount accessory plate allows you to mount just about anything you can think of on top of your FS-700. The plate is loaded with tapped holes in both the Berkey System standard and in RED standard spacing so that you can use any of our standard 15 mm accessories or any of our RED accessories to customize your FS-700 for your shooting style. Add handles, monitors, EVF's, top mount iris rods and more...way more than I can think of at this late hour. Read the rest of this entry »

Gain control of your controls! Here's the simplest way to relocate you factory Sony handle for the FS-700. With the 15 mm Right Angle Block, the Rosette Spud and the 18 inch extension cable you can now relocate your Sony control handle to the front rails of your rig and be able to utilize the factory on/off and zoom controls from a useable position.  Kit includes one Rosette Spud, one 15 mm Right Angle Block and one 18 inch Extension Cable.

Use this Rosette Spud to relocate your Sony FS-700 factory handle allowing you to use the factory on/off and zoom controls. To use, simply screw the Rosette Spud onto your factory handle and using any combination of our blocks and rods (sold separately) and place the handle just where you like it. You can now run your factory grip ENG style out front or on top or anywhere else you might like it. Includes one 18 inch extension cable.

If you want to mount accessories on the rosette on the side of your FS-700 we have the solution - the Rosette Spud. This rosette has a counter-bored hole through the center allowing you to fasten it to the side of the camera on the Sony factory rosette. From there you can add just about any of our 15 mm based blocks (sold separately). Includes one 1/4-20 X 3/4 fastener.

Light duty linear mover based on the 375 series component group. Built-in NEMA 17 motor mount allows the use of steppers or servo motors. Many uses. Max length, 24 inches. Made to order. Motor not included

We have them in stock and ready to ship. Lots of mounting holes and a viewfinder cable strain protector. Comes with all fasteners needed. More info soon.